Zen

Translation

Nc_Strs.SNoNcCmds
Chinese (Simplified)
没有可供加工的指令，请检查是否存在加工图形，或选择了只加工选中图形
81/330 · 33

Sign in to save the translation.

Context Chinese (Simplified) English Actions
Nc_Strs.SNextCurveWillBeyondY1PosRange
下一条轨迹即将超过Y1正行程, 必须触发状态切换
Next path will exceed Y1 +range, must trigger status switching
Nc_Strs.SNextStateUnKnown
下个状态未知
nest state unknown
Nc_Strs.SNextTapCannotForward
非攻丝轨迹无法前进到攻丝孔
Non tapping hole cannot forward to tapping path
Nc_Strs.SNextTraceNeedAutoFeedErr
下一条轨迹需要送料切割，无法继续前进
Next Curve Need AutoFeed and Cannot Move Error
Nc_Strs.SNoAfterChangePLC
没有切换后PLC
No after-switch PLC
Nc_Strs.SNoBJogWhileChuckBusy
卡盘松开/夹紧过程中，不允许 B 轴运动
Axis-B jogging not allowed while chuck is busy
Nc_Strs.SNoBeforeChangePLC
没有切换前PLC
No before-switch PLC
Nc_Strs.SNoCanPick
无法捡料！
Cannot pick up the material!
Nc_Strs.SNoChannel
图形不存在图层%s，请设置好图层%s参数后再进行一键切断
The graphic does not have layer %s. Please set the layer %s parameters first.
Nc_Strs.SNoFile
没有打开文件
No file opened
Nc_Strs.SNoFileOrFileError
没有图纸或图纸解析失败
No file or file error
Nc_Strs.SNoJogWithAssistChuckOn
检测到当前中卡辅助卡盘是夹紧状态，请松开辅助卡盘后再发送运动指令
It is detected that the current middle card Assist chuck is in a clamping state. Please unclamp the Assist chuck and then send the Move Cmds
Nc_Strs.SNoLastPipeTail
转盘机型, 不允许在最后一个零件切割之前触发零尾料！
WheelChuck model, forbid to trigger ZeroTail process before the last part is cut
Nc_Strs.SNoLoopCount
已经到了计划循环次数，不允许再次加工
The number of planned cycles is not allowed to be processed again
Nc_Strs.SNoMidChuck
没有配置中卡
MidChuck is not configured
Nc_Strs.SNoNcCmds
没有可供加工的指令，请检查是否存在加工图形，或选择了只加工选中图形
No commands found!
Did you choose only cut selected graphics, or select no curve?
Nc_Strs.SNoRoundPipe
非圆管，无法进行辅助夹持切割
Not a round pipe
Nc_Strs.SNoTailClose
未开启零尾料功能，无法用零尾料切割
ZeroTail not enabled, cannot start ZeroTail cutting
Nc_Strs.SNoY3B4
未配置 Y3B4 卡爪，无法进行辅助夹持！
Y3B4 not configured!
Nc_Strs.SNolinearError
非线性拟合数据错误
Non-linear fitting data error
Nc_Strs.SNonEcCantSetServo
参数设置仅支持总线版系统
Servo Param. Setting only Available for EtherCAT System
Nc_Strs.SNoneAfterDodgePLCErr
未配置避让后PLC！
After-dodge not set
Nc_Strs.SNoneAfterNoTailPLCErr
未配置零尾料后PLC！
After ZeroTail PLC not configured
Nc_Strs.SNoneBeforeDodgePLCErr
未配置避让前PLC！
Before-dodge PLC not set
Nc_Strs.SNoneBeforeNoTailPLCErr
未配置零尾料前PLC！
Before ZeroTail PLC not configured
Nc_Strs.SNoneDodgePLCErr
未配置避让前PLC！
Before-dodge PLC not set
Nc_Strs.SNoneFeedLoadPLC
未配置上料PLC！
Loading PLC not configured!
Nc_Strs.SNotAllowCurrnetPLCSteps
调高器处于安全模式下，禁止执行包含 X/Y/B 轴动作的PLC！
Safe Follower Mode, X/Y/B-axis motion PLC prohibited!
Nc_Strs.SNotAllowOverSize
当前文件尺寸%.2fX%.2f,超过卡盘尺寸%.2fX%.2f,无法加工
Current file size%.2fX%.2f exceeds the chuck size %.2fX%.2f. Cannot cut
Nc_Strs.SNotAllowUnloaderDynamic
没有打开图纸, 禁止使用下料板随动支撑
No file is open. The unloading Follow holder is prohibited!
Nc_Strs.SNotAllowUpByCongig
执行过支架禁止上升，需要执行对应的允许上升plc后才能上升
Holder has Forbidden up by PLC. Please execute Allow-Up PLC
Context Chinese (Simplified) English Actions
Nc_Strs.SNextCurveWillBeyondY1PosRange
下一条轨迹即将超过Y1正行程, 必须触发状态切换
Next path will exceed Y1 +range, must trigger status switching
Nc_Strs.SNextStateUnKnown
下个状态未知
nest state unknown
Nc_Strs.SNextTapCannotForward
非攻丝轨迹无法前进到攻丝孔
Non tapping hole cannot forward to tapping path
Nc_Strs.SNextTraceNeedAutoFeedErr
下一条轨迹需要送料切割，无法继续前进
Next Curve Need AutoFeed and Cannot Move Error
Nc_Strs.SNoAfterChangePLC
没有切换后PLC
No after-switch PLC
Nc_Strs.SNoBJogWhileChuckBusy
卡盘松开/夹紧过程中，不允许 B 轴运动
Axis-B jogging not allowed while chuck is busy
Nc_Strs.SNoBeforeChangePLC
没有切换前PLC
No before-switch PLC
Nc_Strs.SNoCanPick
无法捡料！
Cannot pick up the material!
Nc_Strs.SNoChannel
图形不存在图层%s，请设置好图层%s参数后再进行一键切断
The graphic does not have layer %s. Please set the layer %s parameters first.
Nc_Strs.SNoFile
没有打开文件
No file opened
Nc_Strs.SNoFileOrFileError
没有图纸或图纸解析失败
No file or file error
Nc_Strs.SNoJogWithAssistChuckOn
检测到当前中卡辅助卡盘是夹紧状态，请松开辅助卡盘后再发送运动指令
It is detected that the current middle card Assist chuck is in a clamping state. Please unclamp the Assist chuck and then send the Move Cmds
Nc_Strs.SNoLastPipeTail
转盘机型, 不允许在最后一个零件切割之前触发零尾料！
WheelChuck model, forbid to trigger ZeroTail process before the last part is cut
Nc_Strs.SNoLoopCount
已经到了计划循环次数，不允许再次加工
The number of planned cycles is not allowed to be processed again
Nc_Strs.SNoMidChuck
没有配置中卡
MidChuck is not configured
Nc_Strs.SNoNcCmds
没有可供加工的指令，请检查是否存在加工图形，或选择了只加工选中图形
No commands found!
Did you choose only cut selected graphics, or select no curve?
Nc_Strs.SNoRoundPipe
非圆管，无法进行辅助夹持切割
Not a round pipe
Nc_Strs.SNoTailClose
未开启零尾料功能，无法用零尾料切割
ZeroTail not enabled, cannot start ZeroTail cutting
Nc_Strs.SNoY3B4
未配置 Y3B4 卡爪，无法进行辅助夹持！
Y3B4 not configured!
Nc_Strs.SNolinearError
非线性拟合数据错误
Non-linear fitting data error
Nc_Strs.SNonEcCantSetServo
参数设置仅支持总线版系统
Servo Param. Setting only Available for EtherCAT System
Nc_Strs.SNoneAfterDodgePLCErr
未配置避让后PLC！
After-dodge not set
Nc_Strs.SNoneAfterNoTailPLCErr
未配置零尾料后PLC！
After ZeroTail PLC not configured
Nc_Strs.SNoneBeforeDodgePLCErr
未配置避让前PLC！
Before-dodge PLC not set
Nc_Strs.SNoneBeforeNoTailPLCErr
未配置零尾料前PLC！
Before ZeroTail PLC not configured
Nc_Strs.SNoneDodgePLCErr
未配置避让前PLC！
Before-dodge PLC not set
Nc_Strs.SNoneFeedLoadPLC
未配置上料PLC！
Loading PLC not configured!
Nc_Strs.SNotAllowCurrnetPLCSteps
调高器处于安全模式下，禁止执行包含 X/Y/B 轴动作的PLC！
Safe Follower Mode, X/Y/B-axis motion PLC prohibited!
Nc_Strs.SNotAllowOverSize
当前文件尺寸%.2fX%.2f,超过卡盘尺寸%.2fX%.2f,无法加工
Current file size%.2fX%.2f exceeds the chuck size %.2fX%.2f. Cannot cut
Nc_Strs.SNotAllowUnloaderDynamic
没有打开图纸, 禁止使用下料板随动支撑
No file is open. The unloading Follow holder is prohibited!

Loading…

None

Automatically translated
没有可供加工的指令，请检查是否存在加工图形，或选择了只加工选中图形
No commands found!
Did you choose only cut selected graphics, or select no curve?
2 months ago
None

String added in the repository
没有可供加工的指令，请检查是否存在加工图形，或选择了只加工选中图形
 
2 months ago
Browse all string changes

Things to check

Mismatched question mark

Source and translation do not both end with a question mark

Reset

Mismatching line breaks

Number of new lines in translation does not match source

Reset

Glossary

Chinese (Simplified) English
加工 Production *TubesT软件术语库

强调整个加工任务
加工 Cut *TubesT软件术语库

强调切割/不切割
选择 Select *TubesT软件术语库

顶部功能菜单标签
选择 Select *TubePro软件术语库

String information

Context
Nc_Strs.SNoNcCmds
Labels
Automatically translated
String age
2 months ago
Last updated
2 months ago
Source string age
2 months ago
Translation file
en.po, string 1416