PlateConfig/PlateConfig/trunk-Maintenance — English @ Weblate: 提示：当前设备没有连接网络，无法下载视觉监控模块。请前往柏楚官网-下载中心自行下载视觉监控模块。地址：www.fscut.com/download/。操作方法： 1. 拷贝模块到本设备。 2. 双击模块，运行安装。 3. …

Translation

Context Config.SMsgManualDownloadBCVMonitor

Chinese (Simplified)

English

Needs editing

Skip

Context	Chinese (Simplified)	English
Config.SMotorHoldB	低位台电机抱闸	PalletB brake
Config.SMotorHoldCloseDelay	电机抱闸关闭延时	Motor brake release delay
Config.SMotorHoldCtrl	电机抱闸控制	Motor brake control
Config.SMotorHoldDelay	电机抱闸延迟	Motor brake delay
Config.SMotorInertia	电机惯量	Motor inertia
Config.SMotorParams	电机参数	Motor Parameters
Config.SMotorPick	异步电机下料	Asynchronous motor feed
Config.SMotorReverse	电机反向	Motor reverse
Config.SMotorType	电机类型	Motor Type
Config.SMotorType1	旋转电机	Rotary motor
Config.SMoveAcc	加速度	Acceleration
Config.SMoveNeedCheck	调高器报警需确认后才能允许轴运动	Height controller alarms release require operator's manual input
Config.SMsgHypConfigCloseTimeOut	平台配置工具还未关闭, HypCut启动失败！	CypConfig is open. Failed to start CypCutPro!
Config.SMsgHypCutCloseTimeOut	HypCut还未关闭, 重启HypCut失败！	CypCutPro is running. Failed to start it!
Config.SMsgHypCutCloseTimeOut2	HypCut还未关闭, 启动平台配置工具失败！	CypCutPro is running. Failed to start the platform configuration tool.
Config.SMsgManualDownloadBCVMonitor	提示：当前设备没有连接网络，无法下载视觉监控模块。请前往柏楚官网-下载中心自行下载视觉监控模块。地址：www.fscut.com/download/。操作方法： 1. 拷贝模块到本设备。 2. 双击模块，运行安装。 3. 安装完毕，在%s里启用监控功能即可调用监控。	Tip:\nThe current device is not connected to the network, so the vision module cannot be downloaded.\ n\nPlease go to the website to download the Vision Module.\ nAddress: www.fscut.com/download/.\ n\nTips:\n1. Copy the module to this device.\ n2. Double-click the module to run the installation.\ n3. After installation, enable the function in %s module.
Config.SMsgSetupBCVMonitor	下载并安装视觉监控组件	Download and install Vision components
Config.SMustServoOffWhenChangeDir	必须在使能关闭的时候才能修改方向，是否关闭使能并反向？	Direction only be changed when the servo is disabled. Disable it and reverse the direction?
Config.SMutil	多横梁	Multi-Gantry
Config.SN2	氮气	N2
Config.SN2AirSharedPortLost	空气/氮气共用气路输出口未设置	Air and N2 shared circuit output port not set
Config.SN2Alarm	氮气报警	N2 alarm
Config.SNeedDisableAxisAndSaveParams	保存该参数需要断使能，是否保存该参数？	Disable the servo to save the parameters. Continue?
Config.SNegInPort	负限位输入口	Neg limit input
Config.SNegLimit	负限位	-Limit
Config.SNegLimitLogic	负限位逻辑	-Limit logic
Config.SNegative	负向	- direction
Config.SNet	相机IP	Camera IP
Config.SNetSlaveDetail	网络从站: %s(%s)	Network slave: %s(%s)
Config.SNetStatus	网络状态	Network State
Config.SNetworkComm	网络通讯	network communication

Context	Chinese (Simplified)	English
Config.SMotorHoldB	低位台电机抱闸	PalletB brake
Config.SMotorHoldCloseDelay	电机抱闸关闭延时	Motor brake release delay
Config.SMotorHoldCtrl	电机抱闸控制	Motor brake control
Config.SMotorHoldDelay	电机抱闸延迟	Motor brake delay
Config.SMotorInertia	电机惯量	Motor inertia
Config.SMotorParams	电机参数	Motor Parameters
Config.SMotorPick	异步电机下料	Asynchronous motor feed
Config.SMotorReverse	电机反向	Motor reverse
Config.SMotorType	电机类型	Motor Type
Config.SMotorType1	旋转电机	Rotary motor
Config.SMoveAcc	加速度	Acceleration
Config.SMoveNeedCheck	调高器报警需确认后才能允许轴运动	Height controller alarms release require operator's manual input
Config.SMsgHypConfigCloseTimeOut	平台配置工具还未关闭, HypCut启动失败！	CypConfig is open. Failed to start CypCutPro!
Config.SMsgHypCutCloseTimeOut	HypCut还未关闭, 重启HypCut失败！	CypCutPro is running. Failed to start it!
Config.SMsgHypCutCloseTimeOut2	HypCut还未关闭, 启动平台配置工具失败！	CypCutPro is running. Failed to start the platform configuration tool.
Config.SMsgManualDownloadBCVMonitor	提示：当前设备没有连接网络，无法下载视觉监控模块。请前往柏楚官网-下载中心自行下载视觉监控模块。地址：www.fscut.com/download/。操作方法： 1. 拷贝模块到本设备。 2. 双击模块，运行安装。 3. 安装完毕，在%s里启用监控功能即可调用监控。	Tip:\nThe current device is not connected to the network, so the vision module cannot be downloaded.\ n\nPlease go to the website to download the Vision Module.\ nAddress: www.fscut.com/download/.\ n\nTips:\n1. Copy the module to this device.\ n2. Double-click the module to run the installation.\ n3. After installation, enable the function in %s module.
Config.SMsgSetupBCVMonitor	下载并安装视觉监控组件	Download and install Vision components
Config.SMustServoOffWhenChangeDir	必须在使能关闭的时候才能修改方向，是否关闭使能并反向？	Direction only be changed when the servo is disabled. Disable it and reverse the direction?
Config.SMutil	多横梁	Multi-Gantry
Config.SN2	氮气	N2
Config.SN2AirSharedPortLost	空气/氮气共用气路输出口未设置	Air and N2 shared circuit output port not set
Config.SN2Alarm	氮气报警	N2 alarm
Config.SNeedDisableAxisAndSaveParams	保存该参数需要断使能，是否保存该参数？	Disable the servo to save the parameters. Continue?
Config.SNegInPort	负限位输入口	Neg limit input
Config.SNegLimit	负限位	-Limit
Config.SNegLimitLogic	负限位逻辑	-Limit logic
Config.SNegative	负向	- direction
Config.SNet	相机IP	Camera IP
Config.SNetSlaveDetail	网络从站: %s(%s)	Network slave: %s(%s)
Config.SNetStatus	网络状态	Network State

Loading…

fuyulu

Translation changed

Chinese (Simplified)

English 24 characters edited Current translation Translated

3 months ago

fuyulu

Automatically translated

Chinese (Simplified)

English 359 characters edited Needs editing

3 months ago

None

String added in the repository

Chinese (Simplified)

English 0 characters edited Empty

3 months ago

Browse all string changes

Things to check

Does not follow glossary Enforced

Following terms are not translated according to glossary: 中, 启用监控, 无, 监控, 视觉监控

Mismatched \n

Number of \n literals in translation does not match source

Reset

Mismatching line breaks

Number of new lines in translation does not match source

Reset

Glossary

Chinese (Simplified)	English
中	Medium	*HypCut Revo软件术语库
启用监控	Enable Monitor	*HypCut软件术语库
无	Null	*HypCut Revo软件术语库
监控	Monitor	*HypCut软件术语库
视觉	Vision	*HypCut软件术语库
视觉监控	Video Monitor	*HypCut Revo软件术语库

String information

Context

Config.SMsgManualDownloadBCVMonitor

Flags

c-sharp-format, check-glossary, object-pascal-format, vue-format

String age

3 months ago

Last updated

2 weeks ago

Source string age

3 months ago

Translation file

en.po, string 990