WeldNck/trunk — English @ Weblate: 对应焊道可能在焊接过程中开启摆焊出现逆解失败的问题

Translation

Context Nck_Strs.SHingMightWcsToMcsFailed

Chinese (Simplified)

English

Needs editing

Skip

Context	Chinese (Simplified)	English
Nck_Strs.SAlgCheckOverSpeedTime	飞车保护判断时间过长:%.4f ms	Overspeed Protection Delay: %.4f ms
Nck_Strs.SAlgTickTime	算法tick时间过长:%.4f ms	Algorithm Tick Overrun: %.4f ms
Nck_Strs.SAxisOverSpeed	启用增量插补！起点关节偏差：	Incremental interpolation enabled! Start joint deviation:
Nck_Strs.SChangeWorkBench	NCK切换工位， WorkbenchIdx:	NCK switching workbench, WorkbenchIdx:
Nck_Strs.SFirstPointCheckTime	起点增量检查耗时过长:%.4f ms	Start Point Verification Delay: %.4f ms
Nck_Strs.SGetAlgStateTime	算法状态获取时间过长:%.4f ms	Algorithm State Timeout: %.4f ms
Nck_Strs.SHingMightWcsToMcsFailed	对应焊道可能在焊接过程中开启摆焊出现逆解失败的问题	Inverse solution failure may occur in the corresponding weld seam due to enabling weaving during the welding process.
Nck_Strs.SHintAxisOutOfRange	请将超限位轴点动到合适位置	Jog the axis that is out of the limit to the appropriate position
Nck_Strs.SHintAxisOutOfRangeWhileMoving	逻辑轴%d运动过程超限位	Logic axis %d motion exceeded limit
Nck_Strs.SHintCreateCollisionDetectorFailed	OnlyCollisionDetector创建失败	Failed to create OnlyCollisionDetector
Nck_Strs.SHintCreateCollisionDetectorSuccess	OnlyCollisionDetector创建成功	OnlyCollisionDetector is created.
Nck_Strs.SHintCurvePoint	第 %d 个点，[%f %f %f %f %f %f]	Point No. %d, [%f %f %f %f %f %f %f]
Nck_Strs.SHintGenerateCurveConsume	生成点动轨迹时间%.2f ms	Jog trajectory generation time %.2f ms
Nck_Strs.SHintStopCnt	停止耗时%d ms	Stopping time %d ms
Nck_Strs.SNCK_ALM_CHECKCURVE	NCK检查轨迹发现异常	NCK detected an abnormality while checking the trajectory.
Nck_Strs.SNCK_ALM_COLLISION	机器人发生碰撞	Robot collided
Nck_Strs.SNCK_ALM_FAST_DECSTOP	NCK快速缓急停失败,交由RTOS处理	Quick braking failed in NCK, handed over to RTOS for handling.
Nck_Strs.SNCK_ALM_FEEDBACK_TORQUE	机器人力矩超限：轴%d, 建议紧固寻缝器并重新标定手眼	Robot torque exceeded: axis %d. It is recommended to secure the seam tracker and recalibrate the hand-eye
Nck_Strs.SNCK_ALM_FIRST_POINT_ERROR	轨迹首点和当前位置不同	The trajectory starting point is different from the current position
Nck_Strs.SNCK_ALM_ITPINIT	初始化插补器异常	Exception occurred during interpolation initialization.
Nck_Strs.SNCK_ALM_NOMCSPTCALC	轨迹Wcs求逆解失败!	Failed to calculate inverse kinematics for the WCS trajectory!
Nck_Strs.SNCK_ALM_NOSTARTPT	起点计算失败!	Failed to calculate the start point!

Context	Chinese (Simplified)	English
Nck_Strs.SAlgCheckOverSpeedTime	飞车保护判断时间过长:%.4f ms	Overspeed Protection Delay: %.4f ms
Nck_Strs.SAlgTickTime	算法tick时间过长:%.4f ms	Algorithm Tick Overrun: %.4f ms
Nck_Strs.SAxisOverSpeed	启用增量插补！起点关节偏差：	Incremental interpolation enabled! Start joint deviation:
Nck_Strs.SChangeWorkBench	NCK切换工位， WorkbenchIdx:	NCK switching workbench, WorkbenchIdx:
Nck_Strs.SFirstPointCheckTime	起点增量检查耗时过长:%.4f ms	Start Point Verification Delay: %.4f ms
Nck_Strs.SGetAlgStateTime	算法状态获取时间过长:%.4f ms	Algorithm State Timeout: %.4f ms
Nck_Strs.SHingMightWcsToMcsFailed	对应焊道可能在焊接过程中开启摆焊出现逆解失败的问题	Inverse solution failure may occur in the corresponding weld seam due to enabling weaving during the welding process.
Nck_Strs.SHintAxisOutOfRange	请将超限位轴点动到合适位置	Jog the axis that is out of the limit to the appropriate position
Nck_Strs.SHintAxisOutOfRangeWhileMoving	逻辑轴%d运动过程超限位	Logic axis %d motion exceeded limit
Nck_Strs.SHintCreateCollisionDetectorFailed	OnlyCollisionDetector创建失败	Failed to create OnlyCollisionDetector
Nck_Strs.SHintCreateCollisionDetectorSuccess	OnlyCollisionDetector创建成功	OnlyCollisionDetector is created.
Nck_Strs.SHintCurvePoint	第 %d 个点，[%f %f %f %f %f %f]	Point No. %d, [%f %f %f %f %f %f %f]
Nck_Strs.SHintGenerateCurveConsume	生成点动轨迹时间%.2f ms	Jog trajectory generation time %.2f ms
Nck_Strs.SHintStopCnt	停止耗时%d ms	Stopping time %d ms
Nck_Strs.SNCK_ALM_CHECKCURVE	NCK检查轨迹发现异常	NCK detected an abnormality while checking the trajectory.
Nck_Strs.SNCK_ALM_COLLISION	机器人发生碰撞	Robot collided
Nck_Strs.SNCK_ALM_FAST_DECSTOP	NCK快速缓急停失败,交由RTOS处理	Quick braking failed in NCK, handed over to RTOS for handling.
Nck_Strs.SNCK_ALM_FEEDBACK_TORQUE	机器人力矩超限：轴%d, 建议紧固寻缝器并重新标定手眼	Robot torque exceeded: axis %d. It is recommended to secure the seam tracker and recalibrate the hand-eye
Nck_Strs.SNCK_ALM_FIRST_POINT_ERROR	轨迹首点和当前位置不同	The trajectory starting point is different from the current position
Nck_Strs.SNCK_ALM_ITPINIT	初始化插补器异常	Exception occurred during interpolation initialization.
Nck_Strs.SNCK_ALM_NOMCSPTCALC	轨迹Wcs求逆解失败!	Failed to calculate inverse kinematics for the WCS trajectory!

Loading…

huanglinxiao

Translation uploaded

Chinese (Simplified)

English 117 characters edited Current translation Translated

12 days ago

None

String added in the repository

Chinese (Simplified)

English 0 characters edited Empty

a month ago

Browse all string changes

Things to check

Mismatched full stop

Source and translation do not both end with a full stop

Reset

Glossary

Chinese (Simplified)	English
No related strings found in the glossary.

String information

Context

Nck_Strs.SHingMightWcsToMcsFailed

String age

a month ago

Last updated

12 days ago

Source string age

4 months ago

Translation file

en.po, string 7