PlateHMI2D/BLT — English @ Weblate: 穿孔次数不足，无法执行清洁喷嘴

Translation

Context Application.SAutoCleanErrorConut

Chinese (Simplified)

English

Needs editing

Skip

Context	Chinese (Simplified)	English
Application.SAsynchronousOnly	仅支持异步调用	Asynchronous call only
Application.SAuthSwitchTo	权限切换为:	Identity switch to:
Application.SAuthTimeOut	权限超时登出	Timeout then logout
Application.SAutoAdjust	自动调整	Auto Adjust
Application.SAutoAdjustNnote	该功能自动调整调高器增益与机械匹配。 1.标定前请确认浮头下方有稳定的板材; 2.先将浮头点动到靠近板面; 3.进行电容标定.	To automatically adjust height follower gain level to match the machinery. 1.Make sure there is stable plate below nozzle; 2.Jog the cutting head close to plate surface; 3.Perform capacitance calibration.
Application.SAutoAdjusting	自动调整中.....	Auto Adjusting...
Application.SAutoCaliErr	一键标定出现异常：	Quick Calibration error:
Application.SAutoCaliNotEnabled	未启用一键标定功能	Quick Calibrate not enabled
Application.SAutoCalibrate	一键标定	Quick Calibrate
Application.SAutoCalibration	一键标定	Quick Calibrate
Application.SAutoCancelSelectionOnly	切塞尺不支持只加工选中, 已自动调整	The feeler gauge does not support “Cut selected only”. It has been auto adjusted
Application.SAutoCenter	2.自动对中焦点设置	2.Autofocus Focus Setting
Application.SAutoCentering	正在自动对中	Auto centering
Application.SAutoChangePallet	已经开启加工完成自动交换工作台	Autochange pallet after production
Application.SAutoCleanCutHead	自动清洁喷嘴	Clean Head
Application.SAutoCleanErrorConut	穿孔次数不足，无法执行清洁喷嘴	Pierce times is < set times. Cannot clean the nozzle.
Application.SAutoCleanErrorPallet	当前交换台未到位，无法执行清洁喷嘴	Pallet is not in place. Cannot clean the nozzle.
Application.SAutoCleanErrorRedo	跳入自动清洁喷嘴状态失败,下次加工重新执行	Failed to start Auto Clean Nozzle. Do it next time.
Application.SAutoCleanErrorRedo2	自动清洁喷嘴未完成,下次加工重新执行	Auto Clean Nozzle is not done. Do it next time.
Application.SAutoCleanErrorState	设定的状态与当前系统状态不符，无法执行清洁喷嘴	The system state does not match the its settings. Cannot clean the nozzle.
Application.SAutoCleanHead	自动清洁喷嘴	Clean Head
Application.SAutoCleanNozzleActive	自动清洁喷嘴	Clean Head
Application.SAutoFindCenter1	一键工件寻中	Quick Centering
Application.SAutoGenerate	工位阵列一键设置	Quick Set Station Array
Application.SAutoNozzle	自动喷嘴	Auto Nozzle
Application.SAutoNozzleConfirm	运动前弹窗确认	Pop-up confirmation before start
Application.SAutoNozzleTest	喷嘴拷机	Nozzle Cycle Test
Application.SAutoNozzleTestNew	喷嘴拷机测试	Nozzle Cycle Test
Application.SAutoPause	自动暂停	Auto Pause
Application.SAutoPauseTimerWaitingForPause	等待暂停	Wait Pause
Application.SAutoPauseTimerWaitingForResume	等待继续	Wait Resume

Context	Chinese (Simplified)	English
Application.SAsynchronousOnly	仅支持异步调用	Asynchronous call only
Application.SAuthSwitchTo	权限切换为:	Identity switch to:
Application.SAuthTimeOut	权限超时登出	Timeout then logout
Application.SAutoAdjust	自动调整	Auto Adjust
Application.SAutoAdjustNnote	该功能自动调整调高器增益与机械匹配。 1.标定前请确认浮头下方有稳定的板材; 2.先将浮头点动到靠近板面; 3.进行电容标定.	To automatically adjust height follower gain level to match the machinery. 1.Make sure there is stable plate below nozzle; 2.Jog the cutting head close to plate surface; 3.Perform capacitance calibration.
Application.SAutoAdjusting	自动调整中.....	Auto Adjusting...
Application.SAutoCaliErr	一键标定出现异常：	Quick Calibration error:
Application.SAutoCaliNotEnabled	未启用一键标定功能	Quick Calibrate not enabled
Application.SAutoCalibrate	一键标定	Quick Calibrate
Application.SAutoCalibration	一键标定	Quick Calibrate
Application.SAutoCancelSelectionOnly	切塞尺不支持只加工选中, 已自动调整	The feeler gauge does not support “Cut selected only”. It has been auto adjusted
Application.SAutoCenter	2.自动对中焦点设置	2.Autofocus Focus Setting
Application.SAutoCentering	正在自动对中	Auto centering
Application.SAutoChangePallet	已经开启加工完成自动交换工作台	Autochange pallet after production
Application.SAutoCleanCutHead	自动清洁喷嘴	Clean Head
Application.SAutoCleanErrorConut	穿孔次数不足，无法执行清洁喷嘴	Pierce times is < set times. Cannot clean the nozzle.
Application.SAutoCleanErrorPallet	当前交换台未到位，无法执行清洁喷嘴	Pallet is not in place. Cannot clean the nozzle.
Application.SAutoCleanErrorRedo	跳入自动清洁喷嘴状态失败,下次加工重新执行	Failed to start Auto Clean Nozzle. Do it next time.
Application.SAutoCleanErrorRedo2	自动清洁喷嘴未完成,下次加工重新执行	Auto Clean Nozzle is not done. Do it next time.
Application.SAutoCleanErrorState	设定的状态与当前系统状态不符，无法执行清洁喷嘴	The system state does not match the its settings. Cannot clean the nozzle.
Application.SAutoCleanHead	自动清洁喷嘴	Clean Head
Application.SAutoCleanNozzleActive	自动清洁喷嘴	Clean Head
Application.SAutoFindCenter1	一键工件寻中	Quick Centering
Application.SAutoGenerate	工位阵列一键设置	Quick Set Station Array
Application.SAutoNozzle	自动喷嘴	Auto Nozzle
Application.SAutoNozzleConfirm	运动前弹窗确认	Pop-up confirmation before start
Application.SAutoNozzleTest	喷嘴拷机	Nozzle Cycle Test
Application.SAutoNozzleTestNew	喷嘴拷机测试	Nozzle Cycle Test
Application.SAutoPause	自动暂停	Auto Pause
Application.SAutoPauseTimerWaitingForPause	等待暂停	Wait Pause

Loading…

mt:weblate

Automatically translated

Chinese (Simplified)

English 53 characters edited Current translation Translated

a month ago

None

String added in the repository

Chinese (Simplified)

English 0 characters edited Empty

3 months ago

Browse all string changes

Things to check

Mismatched full stop

Source and translation do not both end with a full stop

Reset

Glossary

Chinese (Simplified)	English
喷嘴	Nozzle	*HypCut Revo软件术语库
执行	Start	*HypCut Revo软件术语库
无	Null	*HypCut Revo软件术语库
清洁喷嘴	Clean Nozzle	*HypCut软件术语库
喷嘴	Nozzle	CypCut软件术语表
清洁喷嘴	Clean nozzle	CypCut软件术语表

String information

Context

Application.SAutoCleanErrorConut

Labels

Automatically translated

Flags

c-sharp-format, object-pascal-format, vue-format

String age

3 months ago

Last updated

a month ago

Source string age

3 months ago

Translation file

en.po, string 125