NcLayer/2024D — English @ Weblate: 在指定范围内未找到边界，寻边过程提前退出！

Translation

Context CMEdgeSeekStr.SEdgeNotFoundInRange

Chinese (Simplified)

English

Needs editing

Skip

Context	Chinese (Simplified)	English
CMEdgeSeekStr.SAdjustCoordinate	校正坐标 %d: (X: %0.2f, Y: %0.2f)	Correction coordinates %d: (X: %0.2f, Y: %0.2f)
CMEdgeSeekStr.SAdjustSeekResult	矫正: (X: %0.2f, Y: %0.2f)	Correction: (X: %0.2f, Y: %0.2f)
CMEdgeSeekStr.SAfterLaserOffError	关激光后动作异常	Abnormal motion before laser off
CMEdgeSeekStr.SAlarm	报警停止	Alarm stop
CMEdgeSeekStr.SBCS100Seek	调高器电容寻边	Height controller capacitance Find Edge
CMEdgeSeekStr.SBeforeLaserOnError	开激光前动作异常	Abnormal motion before laser on
CMEdgeSeekStr.SCanNotCurve	无法完成切割	Cannot finish cutting
CMEdgeSeekStr.SCheckHTooSmallStopSeekEdge	检测到电容感应距离过小，寻边失败！	Capacitive sensing distance is too small. FindEdge failed!
CMEdgeSeekStr.SCircleNotAccurate	寻中结果可能存在偏差	Centering results may be deviated
CMEdgeSeekStr.SCircleSeek	圆板寻中	Circle center
CMEdgeSeekStr.SCurBcs100H	GFollower.GetCurHeight is : %.4f	GFollower.GetCurHeight is : %.4f
CMEdgeSeekStr.SCurveOutofRange	轨迹超出幅面范围	Path out of working range
CMEdgeSeekStr.SEdgeAngleCoarse	粗寻边角度	Coarse FindEdge angle
CMEdgeSeekStr.SEdgeAngleFine	精寻边角度	Fine FindEdge angle
CMEdgeSeekStr.SEdgeFoundFmt	已找到边界，位置：%.2f, %.2f	Edge is found, position: %.2f, %.2f
CMEdgeSeekStr.SEdgeNotFoundInRange	在指定范围内未找到边界，寻边过程提前退出！	The edge is not found within the specified area. Program exits.
CMEdgeSeekStr.SEdgeOutDisSmallerThanEdgeAdjust	出边距离小于边缘校正值	EdgeOut distance is less than correction value.
CMEdgeSeekStr.SEdgeResult	矫正: (X: %0.2f, Y: %0.2f)	Correction: (X: %0.2f, Y: %0.2f)
CMEdgeSeekStr.SEdgeSeek	寻边	Find Edge
CMEdgeSeekStr.SEdgeSeekCircleResultFmt	寻中完成，圆心(%.2f, %.2f)，参考直径 %.2fmm	Centering completed, Center(%.2f, %.2f), Reference diameter %.2fmm
CMEdgeSeekStr.SEdgeSeekCircleResultFmtWithoutRadius	寻中完成，圆心(%.2f, %.2f)mm	Centering completed. Center(%.2f, %.2f) mm
CMEdgeSeekStr.SEdgeSeekCircularStartPnt	寻边起始点为：(%.2f, %.2f)	FindEdge StartPt:(%.2f,%.2f)
CMEdgeSeekStr.SEdgeSeekCircularbasePnt	基准点为：(%.2f, %.2f)	Reference point:(%.2f, %.2f)
CMEdgeSeekStr.SEdgeSeekJustInit	还未执行过寻边	No FindEdge done
CMEdgeSeekStr.SEdgeSeekNotSupported	当前不支持给定的寻边类型	Given FindEdge type is not supported
CMEdgeSeekStr.SEdgeSeekRecord	第%d次检测，边界位置：%.2f, %.2f	Check %d times, edge position: %.2f, %.2f
CMEdgeSeekStr.SEdgeSeekResultFmt	寻边完成，旋转角度：%.2f度	FindEdge finished, rotation angle:%.2f
CMEdgeSeekStr.SExtFollowOutStop	板外跟随的加工过程中检测到出边	EdgeOut detected during cutting (out-plate)
CMEdgeSeekStr.SFeederSeek	齿条卷料寻边	Slat coiling FindEdge
CMEdgeSeekStr.SFindInEdge	向内寻边找到边界，坐标为%f	Edge found inward, coordinates:%f
CMEdgeSeekStr.SFindOutEdge	向外寻边找到边界，坐标为%f	Edge found outward, coordinates:%f

Context	Chinese (Simplified)	English
CMEdgeSeekStr.SAdjustCoordinate	校正坐标 %d: (X: %0.2f, Y: %0.2f)	Correction coordinates %d: (X: %0.2f, Y: %0.2f)
CMEdgeSeekStr.SAdjustSeekResult	矫正: (X: %0.2f, Y: %0.2f)	Correction: (X: %0.2f, Y: %0.2f)
CMEdgeSeekStr.SAfterLaserOffError	关激光后动作异常	Abnormal motion before laser off
CMEdgeSeekStr.SAlarm	报警停止	Alarm stop
CMEdgeSeekStr.SBCS100Seek	调高器电容寻边	Height controller capacitance Find Edge
CMEdgeSeekStr.SBeforeLaserOnError	开激光前动作异常	Abnormal motion before laser on
CMEdgeSeekStr.SCanNotCurve	无法完成切割	Cannot finish cutting
CMEdgeSeekStr.SCheckHTooSmallStopSeekEdge	检测到电容感应距离过小，寻边失败！	Capacitive sensing distance is too small. FindEdge failed!
CMEdgeSeekStr.SCircleNotAccurate	寻中结果可能存在偏差	Centering results may be deviated
CMEdgeSeekStr.SCircleSeek	圆板寻中	Circle center
CMEdgeSeekStr.SCurBcs100H	GFollower.GetCurHeight is : %.4f	GFollower.GetCurHeight is : %.4f
CMEdgeSeekStr.SCurveOutofRange	轨迹超出幅面范围	Path out of working range
CMEdgeSeekStr.SEdgeAngleCoarse	粗寻边角度	Coarse FindEdge angle
CMEdgeSeekStr.SEdgeAngleFine	精寻边角度	Fine FindEdge angle
CMEdgeSeekStr.SEdgeFoundFmt	已找到边界，位置：%.2f, %.2f	Edge is found, position: %.2f, %.2f
CMEdgeSeekStr.SEdgeNotFoundInRange	在指定范围内未找到边界，寻边过程提前退出！	The edge is not found within the specified area. Program exits.
CMEdgeSeekStr.SEdgeOutDisSmallerThanEdgeAdjust	出边距离小于边缘校正值	EdgeOut distance is less than correction value.
CMEdgeSeekStr.SEdgeResult	矫正: (X: %0.2f, Y: %0.2f)	Correction: (X: %0.2f, Y: %0.2f)
CMEdgeSeekStr.SEdgeSeek	寻边	Find Edge
CMEdgeSeekStr.SEdgeSeekCircleResultFmt	寻中完成，圆心(%.2f, %.2f)，参考直径 %.2fmm	Centering completed, Center(%.2f, %.2f), Reference diameter %.2fmm
CMEdgeSeekStr.SEdgeSeekCircleResultFmtWithoutRadius	寻中完成，圆心(%.2f, %.2f)mm	Centering completed. Center(%.2f, %.2f) mm
CMEdgeSeekStr.SEdgeSeekCircularStartPnt	寻边起始点为：(%.2f, %.2f)	FindEdge StartPt:(%.2f,%.2f)
CMEdgeSeekStr.SEdgeSeekCircularbasePnt	基准点为：(%.2f, %.2f)	Reference point:(%.2f, %.2f)
CMEdgeSeekStr.SEdgeSeekJustInit	还未执行过寻边	No FindEdge done
CMEdgeSeekStr.SEdgeSeekNotSupported	当前不支持给定的寻边类型	Given FindEdge type is not supported
CMEdgeSeekStr.SEdgeSeekRecord	第%d次检测，边界位置：%.2f, %.2f	Check %d times, edge position: %.2f, %.2f
CMEdgeSeekStr.SEdgeSeekResultFmt	寻边完成，旋转角度：%.2f度	FindEdge finished, rotation angle:%.2f
CMEdgeSeekStr.SExtFollowOutStop	板外跟随的加工过程中检测到出边	EdgeOut detected during cutting (out-plate)
CMEdgeSeekStr.SFeederSeek	齿条卷料寻边	Slat coiling FindEdge
CMEdgeSeekStr.SFindInEdge	向内寻边找到边界，坐标为%f	Edge found inward, coordinates:%f

Loading…

xiongjintao

Automatically translated

Chinese (Simplified)

English 63 characters edited Current translation Translated

2 months ago

None

String added in the repository

Chinese (Simplified)

English 0 characters edited Empty

4 months ago

Browse all string changes

Things to check

Mismatched exclamation mark

Source and translation do not both end with an exclamation mark

Reset

Mismatched full stop

Source and translation do not both end with a full stop

Reset

Glossary

Chinese (Simplified)	English
寻边	Find Edge	*HypCut软件术语库
【寻边】按钮
寻边	Find edge	CypCut软件术语表
寻边	Find Edge	FACut软件术语表

String information

Context

CMEdgeSeekStr.SEdgeNotFoundInRange

Labels

Automatically translated

Flags

c-sharp-format, object-pascal-format, vue-format

String age

4 months ago

Last updated

2 months ago

Source string age

4 months ago

Translation file

en.po, string 31