KDCCommon/KDCCommon/trunk — English @ Weblate: 双驱位置偏差过大

Translation

Context NCKCORE.SAxisAlmGantryDifLarge

Chinese (Simplified)

English

Needs editing

Skip

Context	Chinese (Simplified)	English
Itp_X.SDimErr	维度检查异常	Dimension check anomaly
Itp_X.SItpNotInitConfig	插补器未初始化	Interpolator not initialized
Itp_X.SItpScProtect	时间切片速度异常	Abnormal time-slice speed
Itp_X.SMetaTooMin	刀路存在异常图元	Abnormal toolpath geometry
Itp_X.SPoleMergeErr	内部规划求解错误	Internal planning solution error
Itp_X.SUnKnownErr	未知错误	Unknown error
Itp_X.SValueCheckErr	求解数据检查异常	Request for data check anomaly
Itp_X.SWrongCurveHandle	刀路地址异常	Toolpath address error
Itp_X.SWrongItpHandle	插补器地址异常	Interpolator address error
NCKCORE.SAxisAccFeedError	加速度反馈过大报警	Acceleration feedback too large
NCKCORE.SAxisAlm	轴	Axis
NCKCORE.SAxisAlmCmdError	飞车保护报警	Motor runaway protection alarm
NCKCORE.SAxisAlmEncoderDirWrong	编码器方向反报警	Encoder direction error alarm
NCKCORE.SAxisAlmEncoderMoveAbnorml	编码器异常动报警	Encoder motion error alarm
NCKCORE.SAxisAlmEncoderNoRespounse	编码器无响应报警	Encoder no response alarm
NCKCORE.SAxisAlmGantryDifLarge	双驱位置偏差过大	Dual-Drive position error too large!
NCKCORE.SAxisAlmMoveOutOfNegRange	空移超出负行程	Travel exceed negative range
NCKCORE.SAxisAlmMoveOutOfPosRange	空移超出正行程	Travel exceed positive range
NCKCORE.SAxisAlmNegLimit	负限位报警	Negative limit alarm
NCKCORE.SAxisAlmNegSoftLimit	负软限位报警	Negative soft limit alarm
NCKCORE.SAxisAlmOrgAbsFailed	回原点异常: 绝对式回原点失败	Return origin error: Failed to absolute return origin
NCKCORE.SAxisAlmOrgBackTouchLimit	回原点异常: 回退阶段触发硬限位	Return origin error: Hard limit triggered when returning
NCKCORE.SAxisAlmOrgCapSingal	回原点异常:捕捉开关信号失败	Return origin error: failed to capture sensor signal
NCKCORE.SAxisAlmOrgCapZFailed	回原点异常:捕捉Z相信号失败	Return origin error: failed to capture Z phase signal
NCKCORE.SAxisAlmOrgNeedGantryInit	回原点异常:龙门双驱误差过大,需要龙门初始化	Return origin error: dual-drive gantry error is too large. Initialize the gantry.
NCKCORE.SAxisAlmOrgNoSensor	回原点异常:找不到原点开关	Return origin error: cannot find origin sensor
NCKCORE.SAxisAlmOrgNoSensorUnkownError	回原点异常:找原点开关触发了未知的死循环	Return origin error: origin sensor triggered an unknown endless loop
NCKCORE.SAxisAlmOrgServoDoNotSupportZCap	回原点异常:驱动器不支持Z相信号回原点	Return origin error: driver doesn't support Z phase signal
NCKCORE.SAxisAlmOrgSingalAlwaysEnable	回原点异常:开关信号一直有效	Return origin error: switch sensor always active
NCKCORE.SAxisAlmOrgWhenAxisIsBusy	回原点异常:运动轴一直处于忙的状态	Return origin error: motor axis keeps been occupied
NCKCORE.SAxisAlmPosDifLarge	位置偏差过大报警	Position error too large

Context	Chinese (Simplified)	English
Itp_X.SDimErr	维度检查异常	Dimension check anomaly
Itp_X.SItpNotInitConfig	插补器未初始化	Interpolator not initialized
Itp_X.SItpScProtect	时间切片速度异常	Abnormal time-slice speed
Itp_X.SMetaTooMin	刀路存在异常图元	Abnormal toolpath geometry
Itp_X.SPoleMergeErr	内部规划求解错误	Internal planning solution error
Itp_X.SUnKnownErr	未知错误	Unknown error
Itp_X.SValueCheckErr	求解数据检查异常	Request for data check anomaly
Itp_X.SWrongCurveHandle	刀路地址异常	Toolpath address error
Itp_X.SWrongItpHandle	插补器地址异常	Interpolator address error
NCKCORE.SAxisAccFeedError	加速度反馈过大报警	Acceleration feedback too large
NCKCORE.SAxisAlm	轴	Axis
NCKCORE.SAxisAlmCmdError	飞车保护报警	Motor runaway protection alarm
NCKCORE.SAxisAlmEncoderDirWrong	编码器方向反报警	Encoder direction error alarm
NCKCORE.SAxisAlmEncoderMoveAbnorml	编码器异常动报警	Encoder motion error alarm
NCKCORE.SAxisAlmEncoderNoRespounse	编码器无响应报警	Encoder no response alarm
NCKCORE.SAxisAlmGantryDifLarge	双驱位置偏差过大	Dual-Drive position error too large!
NCKCORE.SAxisAlmMoveOutOfNegRange	空移超出负行程	Travel exceed negative range
NCKCORE.SAxisAlmMoveOutOfPosRange	空移超出正行程	Travel exceed positive range
NCKCORE.SAxisAlmNegLimit	负限位报警	Negative limit alarm
NCKCORE.SAxisAlmNegSoftLimit	负软限位报警	Negative soft limit alarm
NCKCORE.SAxisAlmOrgAbsFailed	回原点异常: 绝对式回原点失败	Return origin error: Failed to absolute return origin
NCKCORE.SAxisAlmOrgBackTouchLimit	回原点异常: 回退阶段触发硬限位	Return origin error: Hard limit triggered when returning
NCKCORE.SAxisAlmOrgCapSingal	回原点异常:捕捉开关信号失败	Return origin error: failed to capture sensor signal
NCKCORE.SAxisAlmOrgCapZFailed	回原点异常:捕捉Z相信号失败	Return origin error: failed to capture Z phase signal
NCKCORE.SAxisAlmOrgNeedGantryInit	回原点异常:龙门双驱误差过大,需要龙门初始化	Return origin error: dual-drive gantry error is too large. Initialize the gantry.
NCKCORE.SAxisAlmOrgNoSensor	回原点异常:找不到原点开关	Return origin error: cannot find origin sensor
NCKCORE.SAxisAlmOrgNoSensorUnkownError	回原点异常:找原点开关触发了未知的死循环	Return origin error: origin sensor triggered an unknown endless loop
NCKCORE.SAxisAlmOrgServoDoNotSupportZCap	回原点异常:驱动器不支持Z相信号回原点	Return origin error: driver doesn't support Z phase signal
NCKCORE.SAxisAlmOrgSingalAlwaysEnable	回原点异常:开关信号一直有效	Return origin error: switch sensor always active
NCKCORE.SAxisAlmOrgWhenAxisIsBusy	回原点异常:运动轴一直处于忙的状态	Return origin error: motor axis keeps been occupied

Loading…

wangyuan

Translation changed

Chinese (Simplified)

English 3 characters edited Current translation Translated

11 days ago

None

String added in the repository

Chinese (Simplified)

English 39 characters edited Translated

4 months ago

Browse all string changes

Things to check

Does not follow glossary

Following terms are not translated according to glossary: 双驱

Reset

Mismatched exclamation mark

Source and translation do not both end with an exclamation mark

Reset

Glossary

Chinese (Simplified)	English
双驱	Dual drive	*HypCut软件术语库
大	Large	*HypCut Revo软件术语库
双驱	Dual drive	CypCut软件术语表

String information

Context

NCKCORE.SAxisAlmGantryDifLarge

Flags

c-sharp-format, check-glossary, object-pascal-format, vue-format

String age

4 months ago

Last updated

11 days ago

Source string age

4 months ago

Translation file

en.po, string 17