Zen

Translation

Judge_Strs.SErrorWarningCurve
Chinese (Simplified)
第%d个零件的第%d条轨迹（轨迹%d）无法加工
39/230 · 23

Sign in to save the translation.

Context Chinese (Simplified) English Actions
Judge_Strs.SB2B3BeforeDodge
B2B3避让前
Before B2B3 Dodge
Judge_Strs.SB2OnlyProcess
将使用B3单卡夹持加工
Will apply single B3 grip
Judge_Strs.SB3AssistB1B2
B3开始辅助夹持B1B2一起加工该零件
B3 will assist B1B2 to process the part
Judge_Strs.SB3BeforeDodge
B3避让前
Before B3 Dodge
Judge_Strs.SB3tateChange
状态切换过程中会出现B3单卡夹持的情况，请关注管材重量
During chuck state transition, single B3 gripping will happen, please take caution to tube weight
Judge_Strs.SCanNotOptimize
无提示优化手段，请您自行检查日志信息或修改配置
No recommendation, please check log or modify the configuration
Judge_Strs.SCanOptimizeState
想要在状态%s 下加工,
To work in %s status,
Judge_Strs.SCanUseMergePart
建议向前合并%d个零件（至少合并%fmm）
It is recommended to merge %d parts forward (at least %f mm)
Judge_Strs.SCanUseShortPartDodge
非重管建议开启【短零件避让】
It is recommended to enable [Short Part Dodge] for light weight tube
Judge_Strs.SCanUseTailReverse
建议使用反切轨迹或往后合并零件
It is recommended to use reverse cut or merge parts backward
Judge_Strs.SCanUseYAlsoDodge
建议开启【同步避让】
It is recommended to enable [Sync Dodge]
Judge_Strs.SCheckPartCloseAndCanNotCut
由于您未勾选了单零件软限位,故为整管模式,所以根据七轴判断为您停止这次切割
[Single Part Soft Limit]not enabled, current is Full Tube mode. Therefore system will stop the cutting based on 7-axis logic
Judge_Strs.SCheckPartOpenAndCanCut
由于您勾选了单零件软限位,故为单零件模式,系统将继续加工,并根据七轴模拟器意见在第%d个零件前停下来
[Single Part Soft Limit] enabled, current is Single Part Mode. System will continue cutting and stop at the %d part by 7-axis simulator
Judge_Strs.SCurPartExceedTube
第%d个零件包围框最大为%f，但管长为%f
The maximum bounding box for part %d is %f, but the tube length is %f
Judge_Strs.SErrorReason
在该轨迹处出现如下问题：
These issues occurred at this toolpath:
Judge_Strs.SErrorWarningCurve
第%d个零件的第%d条轨迹（轨迹%d）无法加工
The part %d path %d(path %d) is invalid
Judge_Strs.SErrorWarningMultiCurve
图纸上第%d个零件的第%d-%d条轨迹无法加工
The path %d to %d of the %d part on the drawing are invalid
Judge_Strs.SErrorWarningPart
第%d个零件无法加工
The %d part unable to process
Judge_Strs.SErrorWarningPath
该图纸无法加工
The drawing is invalid
Judge_Strs.SHintStateChangeLeaveMidChuck
状态切换过程中会出现B1单卡夹持的情况，请关注管材重量
During chuck state transition, single B1 gripping will happen, please take caution to tube weight
Judge_Strs.SHintWarning
第%d个零件的第%d条轨迹（轨迹%d）会进行以下动作:
The path %d (path %d ) of part %d will perform the following actions:
Judge_Strs.SHintWarningMultiCurve
第%d个零件的第%d-%d条轨迹会进行以下动作:
The %d-%d path of part %d will perform the following actions:
Judge_Strs.SMergeWarningNeedCurveReverse
该合并零件会造成需要反切轨迹
The merged part will require reversed cutting
Judge_Strs.SMergeWarningStayInMidChuck
该合并零件会造成要下料的零件卡在中卡里，需要手动下料
This merged part will cause the unloading part get stuck in the middle chuck, requiring manual unloading
Judge_Strs.SMsgToUser
用户提示：
Tips:
Judge_Strs.SNoErrAndNoOptimize
当前图纸可以正常加工
The current drawing is valid
Judge_Strs.SNotFindSafeB3ClampLocation
当前状态%s 没有找到合适的B3夹持位置
Current status %s No suitable B3 grip position found
Judge_Strs.SOptimizeWarning
第%d个零件的第%d条轨迹发生的问题, 可以尝试使用以下方法来解决:
Error occurred at path %d of part %d, you can try the followings methods:
Judge_Strs.SOptimizeWarningMultiCurve
第%d个零件的第%d-%d条轨迹发生的问题, 可以尝试使用以下方法来解决:
Error occurred at path %d-%d of part %d, you can try the following methods:
Judge_Strs.SPathExceedTube
该图纸无法加工完毕，因为图纸长度%f 大于管材长度%f
The drawing cannot finish the production because the drawing length %f is larger than the tube length %f
Judge_Strs.SProcessPartWillExceedY2Pos
该零件无法加工完成, 零件长度为%f, Y2正临界位置到切割头的距离%f, 加工零件可能会撞B3卡盘
The part cannot be processed completely. The part length is %f, the distance from the Y2 critical position to the cutting head is %f, it might collide with B3 chuck
Context Chinese (Simplified) English Actions
Judge_Strs.SB2B3BeforeDodge
B2B3避让前
Before B2B3 Dodge
Judge_Strs.SB2OnlyProcess
将使用B3单卡夹持加工
Will apply single B3 grip
Judge_Strs.SB3AssistB1B2
B3开始辅助夹持B1B2一起加工该零件
B3 will assist B1B2 to process the part
Judge_Strs.SB3BeforeDodge
B3避让前
Before B3 Dodge
Judge_Strs.SB3tateChange
状态切换过程中会出现B3单卡夹持的情况，请关注管材重量
During chuck state transition, single B3 gripping will happen, please take caution to tube weight
Judge_Strs.SCanNotOptimize
无提示优化手段，请您自行检查日志信息或修改配置
No recommendation, please check log or modify the configuration
Judge_Strs.SCanOptimizeState
想要在状态%s 下加工,
To work in %s status,
Judge_Strs.SCanUseMergePart
建议向前合并%d个零件（至少合并%fmm）
It is recommended to merge %d parts forward (at least %f mm)
Judge_Strs.SCanUseShortPartDodge
非重管建议开启【短零件避让】
It is recommended to enable [Short Part Dodge] for light weight tube
Judge_Strs.SCanUseTailReverse
建议使用反切轨迹或往后合并零件
It is recommended to use reverse cut or merge parts backward
Judge_Strs.SCanUseYAlsoDodge
建议开启【同步避让】
It is recommended to enable [Sync Dodge]
Judge_Strs.SCheckPartCloseAndCanNotCut
由于您未勾选了单零件软限位,故为整管模式,所以根据七轴判断为您停止这次切割
[Single Part Soft Limit]not enabled, current is Full Tube mode. Therefore system will stop the cutting based on 7-axis logic
Judge_Strs.SCheckPartOpenAndCanCut
由于您勾选了单零件软限位,故为单零件模式,系统将继续加工,并根据七轴模拟器意见在第%d个零件前停下来
[Single Part Soft Limit] enabled, current is Single Part Mode. System will continue cutting and stop at the %d part by 7-axis simulator
Judge_Strs.SCurPartExceedTube
第%d个零件包围框最大为%f，但管长为%f
The maximum bounding box for part %d is %f, but the tube length is %f
Judge_Strs.SErrorReason
在该轨迹处出现如下问题：
These issues occurred at this toolpath:
Judge_Strs.SErrorWarningCurve
第%d个零件的第%d条轨迹（轨迹%d）无法加工
The part %d path %d(path %d) is invalid
Judge_Strs.SErrorWarningMultiCurve
图纸上第%d个零件的第%d-%d条轨迹无法加工
The path %d to %d of the %d part on the drawing are invalid
Judge_Strs.SErrorWarningPart
第%d个零件无法加工
The %d part unable to process
Judge_Strs.SErrorWarningPath
该图纸无法加工
The drawing is invalid
Judge_Strs.SHintStateChangeLeaveMidChuck
状态切换过程中会出现B1单卡夹持的情况，请关注管材重量
During chuck state transition, single B1 gripping will happen, please take caution to tube weight
Judge_Strs.SHintWarning
第%d个零件的第%d条轨迹（轨迹%d）会进行以下动作:
The path %d (path %d ) of part %d will perform the following actions:
Judge_Strs.SHintWarningMultiCurve
第%d个零件的第%d-%d条轨迹会进行以下动作:
The %d-%d path of part %d will perform the following actions:
Judge_Strs.SMergeWarningNeedCurveReverse
该合并零件会造成需要反切轨迹
The merged part will require reversed cutting
Judge_Strs.SMergeWarningStayInMidChuck
该合并零件会造成要下料的零件卡在中卡里，需要手动下料
This merged part will cause the unloading part get stuck in the middle chuck, requiring manual unloading
Judge_Strs.SMsgToUser
用户提示：
Tips:
Judge_Strs.SNoErrAndNoOptimize
当前图纸可以正常加工
The current drawing is valid
Judge_Strs.SNotFindSafeB3ClampLocation
当前状态%s 没有找到合适的B3夹持位置
Current status %s No suitable B3 grip position found
Judge_Strs.SOptimizeWarning
第%d个零件的第%d条轨迹发生的问题, 可以尝试使用以下方法来解决:
Error occurred at path %d of part %d, you can try the followings methods:
Judge_Strs.SOptimizeWarningMultiCurve
第%d个零件的第%d-%d条轨迹发生的问题, 可以尝试使用以下方法来解决:
Error occurred at path %d-%d of part %d, you can try the following methods:
Judge_Strs.SPathExceedTube
该图纸无法加工完毕，因为图纸长度%f 大于管材长度%f
The drawing cannot finish the production because the drawing length %f is larger than the tube length %f

Loading…

None

String added in the repository
第%d个零件的第%d条轨迹（轨迹%d）无法加工
The part %d path %d(path %d) is invalid
3 weeks ago
Browse all string changes

Things to check

Consecutive duplicated words Enforced

Text contains the same word twice in a row: path

Glossary

Chinese (Simplified) English
加工 Production *TubesT软件术语库

强调整个加工任务
加工 Cut *TubesT软件术语库

强调切割/不切割
加工 Production *HypCut软件术语库

String information

Context
Judge_Strs.SErrorWarningCurve
Flags
c-sharp-format, object-pascal-format, vue-format
String age
3 weeks ago
Last updated
3 weeks ago
Source string age
3 weeks ago
Translation file
en.po, string 465